Rule · CMS calculator

The force on a cleat

estimated

cms.rule.cleatForce

The force a fault puts between the conductors, per metre of cable, and so on each cleat holding them.

Local graph

Leans on · 5Leaned on by · 1Cable cleat calculation workbook — derived from · the force method, publishedCable cleat calculationworkbookderived from · the forcemethodBS EN IEC 61914 — cable cleats — named by · Annex A, publishedBS EN IEC 61914 — cablecleatsnamed by · Annex ACable catalogue — fed by, estimatedCable cataloguefed byInsulation thickness — fed by, estimatedInsulation thicknessfed byFormation constants K — fed by, publishedFormation constants Kfed byCable cleat check — feeds, estimatedCable cleat checkfeedsThe force on a cleat Leans on · 5Leaned on by · 1Cable cleat calculation workbook — derived from · the force method, publishedCable cleatcalculationworkbookderived from · theforce methodBS EN IEC 61914 — cable cleats — named by · Annex A, publishedBS EN IEC 61914— cable cleatsnamed by · Annex ACable catalogue — fed by, estimatedCable cataloguefed byInsulation thickness — fed by, estimatedInsulationthicknessfed byFormation constants K — fed by, publishedFormationconstants Kfed byCable cleat check — feeds, estimatedCable cleat checkfeedsThe force on acleat Leans on · 5Leaned on by · 1Cable cleat calculation workbook — derived from · the force method, publishedCable cleatcalculationworkbookderived from · theforce methodBS EN IEC 61914 — cable cleats — named by · Annex A, publishedBS EN IEC61914 — cablecleatsnamed by · AnnexACable catalogue — fed by, estimatedCablecataloguefed byInsulation thickness — fed by, estimatedInsulationthicknessfed byFormation constants K — fed by, publishedFormationconstants Kfed byCable cleat check — feeds, estimatedCable cleatcheckfeedsThe force on a cleat

publishedestimateda choiceno sourceArrows: the way the data flows

See it in the whole calculator

How the calculator uses it

F′ = K × Iₚₖ² ÷ S · Fₜ = F′ × spacing · Lₘₐₓ = Fᵣ ÷ (F′ × FoS)

Units. F′ comes out in N/m when Iₚₖ is in kA and S in metres: K carries the units (N/kA²). The sheet prints S in millimetres, so divide it by 1,000 first. Fₜ and Fᵣ are in newtons; the spacing and Lₘₐₓ are in metres.

The force per metre is K times the square of the peak current, divided by the spacing between the conductors — in newtons per metre when the current is in kiloamps and the spacing in metres, the units K is given in. Each cleat holds one gap's length of it. The check takes the cleat's rated withstand, divided by the factor of safety, as what one cleat may carry — so the longest gap is that, divided by the force per metre — and on a ladder rounds it DOWN to whole rungs. For a multicore cable the spacing is the estimated core pair, not the cable's outside diameter.

Watch for

It is a conservative design check: it takes every gap as equal and an estimated core spacing. Verify the rating with the cleat's maker before issue.

Worked through on the owner’s ladder run — 4 × XLPE/SWA/LSOH 4c 95mm², cleated on every rung — the cleat working as the calculator prints it

Cleat2LSF07 — Two-Bolt LSF Nylon Cleats
Cable checkedA1 — XLPE/SWA/LSOH 4c 95mm²
FormationMulti-core 3C/4C/5C — K = 0.17 (set from the cables)
Conductor spacing S13.2 mm
S, made up11.0 mm conductor + 2 × 1.1 mm insulation = 13.2 mm — the insulation row this cable used, which the workbook attributes to BS 5467 / BS 6724
Peak short-circuit current20.0 kA peak
Force per metre5152 N/m
F′ in the formula’s units0.17 × 20.0² ÷ 0.013198 m = 5,152 N/m (Iₚₖ in kA, S in metres)
Cleat spacing used300 mm
Force per cleat1546 N
Design force (Fₜ × FoS)1546 N
Rated withstand10000 N — typed
Maximum spacing1941 mm
Recommended spacing1800 mm
VerdictPASS

The rows of the calculation sheet the calculator prints for this run — not typed.

VERIFY before issue

S FOR A MULTI-CORE CABLE IS THE ADJACENT CORE PAIR, NOT THE CABLE'S OUTSIDE DIAMETER. S = (d + 2t) with d = 2·√(A/π), transcribed from Sparkline's Cable Cleat Calculator v3 (Cable Data sheet). The solid-round d under-states a stranded conductor, which over-states the force — an assumption that can only make the answer worse.

coreGeometry.method — the calculator’s own words, not a copy