Constant · CMS calculator
Insulation thickness
estimatedcms.constant.insulationThickness
The insulation on one conductor, by conductor size. It sets how far apart the cores of a multicore cable sit — and the force between them goes as one over that spacing.
Local graph
publishedestimateda choiceno sourceArrows: the way the data flows
The table we actually use
| Conductor mm² | Insulation t mm | From | State |
|---|---|---|---|
| 6.0 | 0.7 | project data | ◐ estimated: project practice, not a standard |
| 25.0 | 0.9 | project data | ◐ estimated: project practice, not a standard |
| 50.0 | 1.0 | project data | ◐ estimated: project practice, not a standard |
| 70.0 | 1.1 | project data | ◐ estimated: project practice, not a standard |
| 150.0 | 1.8 | project data | ◐ estimated: disputed: one of three project rows whose thickness falls as the conductor grows — insulation does not thin, so one of them is wrong |
| 185.0 | 1.6 | project data | ◐ estimated: disputed: one of three project rows whose thickness falls as the conductor grows — insulation does not thin, so one of them is wrong |
| 240.0 | 1.7 | project data | ◐ estimated: disputed: one of three project rows whose thickness falls as the conductor grows — insulation does not thin, so one of them is wrong |
7 rows · 7 marked estimated (hover the mark for why) · read live from tools/cleats/core-geometry.js INSULATION_T
12 more rows are withheld. The calculator holds them, but the workbook attributes them to BS 5467 / BS 6724, a BSI standard we cite only — a transcription does not make that table ours to publish. Only the value a real calculation used is shown, in the worked example below.
How the calculator uses it
The spacing between a multicore cable's cores is the conductor's diameter plus twice this thickness (the force on a cleat).
Only the rows from Sparkline's project data are shown. The rest the workbook attributes to the cable standards; the calculator uses them, but a BSI table is cited, never published, so the worked example shows only the one row a real run used.
Where the sources disagree
Insulation does not thin as a conductor grows — except in three rows here, all from project data, where it does. One of them is wrong, and it matters in one direction: a thickness too large gives a spacing too large and so a force too small. They are flagged, reported and left exactly as Sparkline's sheet has them — nothing is smoothed over.
Worked through on the owner’s ladder run — 4 × XLPE/SWA/LSOH 4c 95mm², cleated on every rung — the cleat working as the calculator prints it
| Cleat | 2LSF07 — Two-Bolt LSF Nylon Cleats |
|---|---|
| Cable checked | A1 — XLPE/SWA/LSOH 4c 95mm² |
| Formation | Multi-core 3C/4C/5C — K = 0.17 (set from the cables) |
| Conductor spacing S | 13.2 mm |
| S, made up | 11.0 mm conductor + 2 × 1.1 mm insulation = 13.2 mm — the insulation row this cable used, which the workbook attributes to BS 5467 / BS 6724 |
| Peak short-circuit current | 20.0 kA peak |
| Force per metre | 5152 N/m |
| F′ in the formula’s units | 0.17 × 20.0² ÷ 0.013198 m = 5,152 N/m (Iₚₖ in kA, S in metres) |
| Cleat spacing used | 300 mm |
| Force per cleat | 1546 N |
| Design force (Fₜ × FoS) | 1546 N |
| Rated withstand | 10000 N — typed |
| Maximum spacing | 1941 mm |
| Recommended spacing | 1800 mm |
| Verdict | PASS |
The rows of the calculation sheet the calculator prints for this run — not typed.
Where the sources disagree
- BS 5467 / BS 6724 — disagrees with: three project rows thin as the conductor grows
VERIFY before issue
INSULATION THICKNESS IS NOT ALL FROM ONE PLACE. Rows marked bs5467 come from a standard this repo does not hold; rows marked project are Sparkline's project cable data — practice, not a standard. Every row carries its own provenance. NOT INTERPOLATED — an untabulated size returns nothing.
coreGeometry.thickness — the calculator’s own words, not a copy
ONE ANOMALY, LEFT AS THE SOURCE HAS IT: t falls from 1.8 mm at 150 mm² to 1.6 mm at 185 mm² and 1.7 mm at 240 mm². Insulation does not thin as a conductor grows, so one of those three is wrong. All three are project-data rows. Confirm against the cable actually specified.
coreGeometry.anomaly — the calculator’s own words, not a copy