Table we keep · CMS calculator

Cleat short-circuit declarations

published

cms.table.cleatDeclarations

What each cleat range has survived, and under which conditions, as the maker publishes it.

Local graph

Leans on · 4Leaned on by · 12F+ two hole clamp — data sheet DS20E — transcribes · p.2, published2F+ two hole clamp — datasheet DS20Etranscribes · p.21F clamps — data sheet DS33E — transcribes · p.2, published1F clamps — data sheetDS33Etranscribes · p.22A clamps — data sheet DS17E — transcribes · p.2, published2A clamps — data sheetDS17Etranscribes · p.2Short-circuit test reports — transcribes · the proposed rated withstand, publishedShort-circuit test reportstranscribes · the proposedrated withstandCable cleat check — feeds, estimatedCable cleat checkfeedsCleat short-circuitdeclarations Leans on · 4Leaned on by · 12F+ two hole clamp — data sheet DS20E — transcribes · p.2, published2F+ two holeclamp — datasheet DS20Etranscribes · p.21F clamps — data sheet DS33E — transcribes · p.2, published1F clamps — datasheet DS33Etranscribes · p.22A clamps — data sheet DS17E — transcribes · p.2, published2A clamps — datasheet DS17Etranscribes · p.2Short-circuit test reports — transcribes · the proposed rated withstand, publishedShort-circuit testreportstranscribes · theproposed ratedwithstandCable cleat check — feeds, estimatedCable cleat checkfeedsCleatshort-circuitdeclarations Leans on · 4Leaned on by · 12F+ two hole clamp — data sheet DS20E — transcribes · p.2, published2F+ two holeclamp — datasheet DS20Etranscribes · p.21F clamps — data sheet DS33E — transcribes · p.2, published1F clamps —data sheetDS33Etranscribes · p.22A clamps — data sheet DS17E — transcribes · p.2, published2A clamps —data sheetDS17Etranscribes · p.2Short-circuit test reports — transcribes · the proposed rated withstand, publishedShort-circuittest reportstranscribes · theproposed ratedwithstandCable cleat check — feeds, estimatedCable cleatcheckfeedsCleat short-circuit declarations

publishedestimateda choiceno sourceArrows: the way the data flows

See it in the whole calculator

The table we actually use

Two-Bolt LSF Nylon Cleats · 2
Tested partCurrent kACleat spacing mmCable Ø mmPhase spacing mmReportState
2F+07LSF80.260036100PDL-17.137.3
2F+142LSF113.01,000117200PDL-15.025.1
Single-Bolt LSF Nylon Cleats · 1
Tested partCurrent kACleat spacing mmCable Ø mmPhase spacing mmReportState
1F (LSF)10.430036100PDL-17.137.2
Two-Bolt Aluminium Cleats (2A) · 2
Tested partCurrent kACleat spacing mmCable Ø mmPhase spacing mmReportState
—183.030036100PDL-18.071.1
—113.0600117200PDL-15.025.1

5 rows · read live from tools/cleats/products.js shortCircuitDeclaration

How the calculator uses it

The cleat check reports the job's fault current against the lowest of these as a bound on the duty — read as a peak, the conservative reading — and says plainly that it is not a spacing selection and not a pass. A range printed untested can reach no short-circuit verdict at any spacing.

Worked through on the owner’s ladder run — 4 × XLPE/SWA/LSOH 4c 95mm², cleated on every rung — the cleat working as the calculator prints it

Cleat2LSF07 — Two-Bolt LSF Nylon Cleats
Cable checkedA1 — XLPE/SWA/LSOH 4c 95mm²
FormationMulti-core 3C/4C/5C — K = 0.17 (set from the cables)
Conductor spacing S13.2 mm
S, made up11.0 mm conductor + 2 × 1.1 mm insulation = 13.2 mm — the insulation row this cable used, which the workbook attributes to BS 5467 / BS 6724
Peak short-circuit current20.0 kA peak
Force per metre5152 N/m
F′ in the formula’s units0.17 × 20.0² ÷ 0.013198 m = 5,152 N/m (Iₚₖ in kA, S in metres)
Cleat spacing used300 mm
Force per cleat1546 N
Design force (Fₜ × FoS)1546 N
Rated withstand10000 N — typed
Maximum spacing1941 mm
Recommended spacing1800 mm
VerdictPASS

The rows of the calculation sheet the calculator prints for this run — not typed.

VERIFY before issue

The two-bolt range declares 80.2 kA at 600 mm intervals (2F+07LSF) and 113 kA at 1 m (2F+142LSF), each with its cable and phase spacing (DS20E issue 04). Each is a bound on the duty survived under those conditions, not a spacing selection; the range is checked against the lower.

cleatProducts.boundNotSelection — the calculator’s own words, not a copy

The single-bolt range (10.0-57.0 mm, where most of the cable catalogue sits) was printed UNTESTED in the catalogue extract; DS33E issue 02 tests its LSF version to 10.4 kA at 300 mm intervals. The calculator still proposes two-bolt cleats only (Sparkline’s rule).

cleatProducts.untestedRange — the calculator’s own words, not a copy

NO RATED TENSILE STRENGTH (Fr) IS PUBLISHED IN THIS EXTRACT. The lateral-load, axial-movement and safe-working-load figures are different quantities and must never be entered as Fr. Fr comes from the product test certificate.

cleatProducts.noFr — the calculator’s own words, not a copy

The 45,239 N in the manufacturer’s calculator report (PDL10.204.2) is not on the data sheet and is not entered as Fr.

cleatProducts.aluminium.frNote — the calculator’s own words, not a copy