Rule · CMS calculator

Flexible conduit fill

published

cms.rule.flexibleFill

The cables' total cross-section — each worked from its outside diameter — may be at most this share of the conduit's cross-section: the inside area the maker prints for PA, the circle of the catalogue's inside diameter for SP and LFH-SP, and for SPL the data sheet's own fill value, which is smaller than its inside. It is the maker's rule, printed at the head of its data sheet for both ranges.

Local graph

Leans on · 1Leaned on by · 1Adaptaflex data sheet — cable carrying capacity — derived from · the rule at the head of each page, publishedAdaptaflex data sheet —cable carrying capacityderived from · the rule at thehead of each pageFill by area — feeds, publishedFill by areafeedsFlexible conduit fill Leans on · 1Leaned on by · 1Adaptaflex data sheet — cable carrying capacity — derived from · the rule at the head of each page, publishedAdaptaflex datasheet — cablecarrying capacityderived from · therule at the head ofeach pageFill by area — feeds, publishedFill by areafeedsFlexible conduitfill Leans on · 1Leaned on by · 1Adaptaflex data sheet — cable carrying capacity — derived from · the rule at the head of each page, publishedAdaptaflex datasheet — cablecarryingcapacityderived from · therule at the headof each pageFill by area — feeds, publishedFill by areafeedsFlexible conduit fill

publishedestimateda choiceno sourceArrows: the way the data flows

See it in the whole calculator

The table we actually use

ConduitCables at most % of the cross-sectionState
Flexible conduit — plastic (Adaptaflex PA)40
Flexible conduit — metal (Adaptaflex SPL)40
Flexible conduit — steel (Adaptaflex SP, LFH-SP)40

3 rows

How the calculator uses it

It is the space factor of a flexible conduit run: the field starts at the maker's figure, and the area check sizes on it against the inside areas, with the future spare kept clear on top. No run length or bends come into it.

Watch for

The maker states the rule for three or more cables. With one or two the calculator still sizes the run, and asks you to confirm with the maker.

Worked through on A flexible conduit run — 6 × LSOH 1c 2.5mm², 3 × LSOH 1c 6mm², no future spare — a conduit starts with none

The conduitFlexible conduit — plastic (Adaptaflex PA)
6 × LSOH 1c 2.5mm²13.8 mm² each, Ø4.2 mm
3 × LSOH 1c 6mm²22.9 mm² each, Ø5.4 mm
Their sum151.8 mm²
28 mm flexible conduit369.8 mm² inside × 40 % = 147.9 mm² — too small for 151.8
34 mm flexible conduit602.6 mm² inside × 40 % = 241.0 mm² — covers 151.8
The conduit the engine chose34 mm — the smallest whose inside area, at the maker’s fill, covers the cables
VerdictPASS — 63.0 % of the usable area

Computed by the calculator for this run when this page was generated — not typed. The inside areas shown are only the cells this run used.

VERIFY before issue

Flexible conduit is sized on Adaptaflex's own rule — the cables' total cross-section at most 40 % of the conduit's cross-section — on the figures of its data sheet (ABB 7TKK001444 02.2021, Table 2: PA standard-weight conduit with Adaptalok fittings; SPL liquidtight with M-Type fittings), the PA 48 mm from the catalogue's inside diameter. ABB's SPL figures are smaller than the conduit's own published inside, which keeps the answer on the safe side. Another maker's conduit of the same nominal size can differ: confirm against the product you specify.

conduitFlexFill — the calculator’s own words, not a copy

Adaptaflex SP and LFH-SP are sized on 40 % of the circle of the inside diameter in ABB's metallic catalogue 7TKK001441 03.2022 (SP p.47, LFH-SP p.45): ABB's fill table does not cover them. The 10 mm is SP only: LFH-SP starts at 12 mm. A fitting's bore can be smaller than the conduit's inside, and another maker's conduit can differ: confirm against the product you specify.

conduitFlexSteel — the calculator’s own words, not a copy

Adaptaflex states its 40 % for three or more cables. With one or two cables, confirm the fill with the maker.

conduitFlexFewCables — the calculator’s own words, not a copy